The second entry lists the severity of the error being reported. The LogLevel directive is used to control the types of errors that are sent to the error log by restricting the severity level. The third entry gives the IP address of the client that generated the error. Beyond that is the message itself, which in this case indicates that the server has been configured to deny the client access.
The server reports the file-system path as opposed to the web path of the requested document. A very wide variety of different messages can appear in the error log. Most look similar to the example above. The error log will also contain debugging output from CGI scripts. Any information written to stderr by a CGI script will be copied directly to the error log. Find centralized, trusted content and collaborate around the technologies you use most.
Connect and share knowledge within a single location that is structured and easy to search. I previously had php 5. I first uninstalled the php 5. I have checked similar questions here in stackoverflow but none of them have helped me so far.
For the record I have the following lines in my httpd. Now apache is showing the source code, but not all of it just part. I added. When you're configuring apache then try to view the page from another browser - I've had days when chrome stubbornly caches the result and it keeps downloading the source code while in another browser it's just fine.
I came across this issue today and none of the solutions described worked for me. So here is another possible cause:. In my case the server did not know the x-mapp-php6 type, since that.
Just removing the AddHandler line from the. If you are prompted to download a. Turns out files shouldn't be stored in mods-enabled , but should rather be stored in mods-available. A symlink should then be created in mods-enabled pointing to the file stored in mods-available.
Regarding the suggestion above that you should tell the browser that you are outputting a PHP script: It seemed like an unusual idea to me. I googled it and found that there is quite a bit of discussion about it on the web.
If Your. This might be happening due to the missing modules required for your php. Assuming you have php7 installed, search available php7 modules using.
Above command will list all available PHP7 modules for installation. You can begin installation of modules like,. I have the same problem. Apache doesn't load php files from a certain website, just downloaded it. I read this post and the answers and I have seen I've got this line into the last place of the. After updating PHP to 7. I previously has a similar issue, after upgrading from 5. I spent two days tracking this and found out that I was putting my PHP scripts in the wrong directory.
I just started PHP work, so I don't know if my solution relates to the version change you went through. I had this problem.
It turned out that I had both nginx and apache installed and automatically starting on boot. The problem was that nginx was binding to the http port first which prevented apache from starting. It's also possible that you have nginx running but your php is set up to run with apache. To verify, run service nginx status and service apache2 status to see which is running.
In the case that nginx is running and apache is not, just run sudo service nginx stop; sudo service apache2 start and your server will now serve php files as expected.
I know that there are 1. So I figured that I would add the solution to my problem here. If I commented these two lines out in my. I have no idea what they do or how they got there, - but it is in every one of my. Tomcat as a windows service: The main benefit for installing tomcat as a windows service is to allow starting it automatically at the startup of the windows. Following are the steps for installing and setting up tomcat as a windows service: Download the windows service installer from here.
Install the downloaded file, pass all the setup until reaching Configuration Options. If you open the windows services, you find a new service called Apache Tomcat 8. Tomcat as a standalone application: If you want to manage manually the startup of tomcat, you can install it as a standalone application through the following steps: Download the tomcat zip file from here.
The Apache Struts web framework is a free open-source solution for creating Java web applications. You can start with Apache Struts using Apache Maven and optionally provided archetypes for easier dependency management and version upgrade.
Or download some of distributions for fully offline development. Use the links below to download a release of Apache Struts from one of our mirrors. You can verify the integrity of the downloaded files using signatures downloaded from our main distribution directory.
0コメント